How To Install Pur Faucet Filter

Download Article

PUR has multiple products available for filtering water, but the filters get less constructive over fourth dimension as they make full with contaminants. How y'all replace the filter depends on which system yous're using. If y'all accept a plastic pitcher or dispenser you keep in the fridge, soak the new filter earlier screwing it in. For filtration systems that attach to your sink faucet, just remove the old filter so you can put the new ane in its place. When you're finished, y'all'll have clean water to drink for another few months!

1
Soak the replacement filter in cold water for xv minutes. Identify the new filter in a clean container that's deep enough then you can fully submerge information technology. Fill the container with cold h2o and leave information technology alone for at to the lowest degree 15 minutes. During this time, any backlog carbon from the filter will lift out and divide then it doesn't get in your drinking water.^[one]
- Soaking the filter also ensures that water flows evenly when you utilize it.
- Don't employ water warmer than 86 °F (30 °C) since it could damage the filter.
Warning: Avoid using third-party filters with your PUR bullpen or dispenser since they may not fit likewise or have been tested as efficiently.
2
Twist the erstwhile filter counterclockwise to remove information technology. Take the lid off of the pitcher or dispenser and set it aside. Then, elevator up the pour tray, which is the blue plastic reservoir on top, and take it out. Catch the cylindrical filter from the lesser and rotate information technology counterclockwise so information technology unhooks from the filter. Pull the old filter out through the pinnacle of the pour tray and throw in the garbage.^[2]
- Wait until the pour tray is empty to change your filter, or else it may be difficult to remove or you may spill.
Advertisement
3
Rinse the new filter nether your faucet for 10 seconds. Accept the filter out of the container when it's finished soaking and hold it underneath your faucet. Plow on common cold water and rotate the filter and then yous can rinse it off completely. After 10 seconds, turn off the water and milk shake out any excess that's nonetheless in the filter.^[3]
- Don't use hot water to rinse the filter off, or else you may damage it.
4
Screw the filter clockwise into the pour tray to secure it. Slide the long, cylindrical part of the filter through the hole in the middle of the pour tray and push it down equally far every bit it goes. Concord the filter by the lesser and rotate it clockwise until you lot hear information technology click into place. Try borer on the end of the filter to brand sure information technology doesn't pop out from the pour tray. Place the pour tray back into the pitcher or dispenser earlier replacing the lid.^[4]
- If the filter does popular out of the cascade tray, and then you didn't properly secure it. Reinsert it and try turning it clockwise over again.
- PUR filters for pitchers and dispensers usually work for 40 gallons (150 50), or approximately 2 months.
five
Hold the Reset button down for v seconds if your bullpen or dispenser has one. Some newer PUR pitchers and dispensers have sensors that detect when yous demand to replace the filter. Right subsequently you replace the filter, press the Reset button on the lid and go along it held down for 5 seconds. A green calorie-free will blink on the lid once the sensor resets.^[5]
- Older pitchers or dispensers may non accept an electronic display.
Ad

1
Unscrew the filtration system from your faucet. Support the weight of the filtration organisation with your nondominant hand then information technology doesn't fall and break. Rotate the plastic locking nut belongings the filtration organisation to the faucet counterclockwise to loosen it. In one case you unscrew the organisation completely, carefully lift it away from the faucet and ready it down on a countertop or towel.^[6]
- Water may spill out from the faucet when yous unscrew the filtration organization.
- Some models of PUR filtration systems may snap onto the faucet. If it doesn't unscrew, try pulling it directly down from the faucet.
two
Twist open the top cover of the system to remove the onetime filter. Hold the filtration organization so the rounded stop of the large cylinder points upwards. Unscrew the pinnacle from the cylinder by rotating it counterclockwise, and prepare the comprehend bated. Pull the sometime filter straight out from the system and throw it away in your trash.^[seven]
- The peak cover is e'er on the reverse end of the spout that dispenses h2o.
3

Set the new filter inside of the system and screw on the embrace. Make sure the narrower end of the filter is on the bottom and the logo is right-side upwards. Place the filter into the filtration organisation so it has a loose fit. Set the elevation cover back over the filter and spiral it into place to secure it.^[8]
iv
Reattach the filtration system to your faucet. Hold the filtration arrangement against the bottom of the faucet so the threadings are perfectly horizontal, or else they won't form a tight seal. Rotate the locking nut clockwise onto the faucet and continue tightening it until it's hand-tight. Turn on the water and make sure information technology doesn't drip or leak at the seam.^[nine]
- If your filtration system doesn't screw on, line it upwards with the faucet and utilize firm pressure to snap it on.
v
Run cold water through the filtration arrangement for 5 minutes. Plow the handle on the right side of the filtration system to divert the h2o through the filter. Let the water to run through the filter for 5 minutes to get rid of whatever residue inside so it works more efficiently. After that, you tin use the filter immediately later on turning it on.^[ten]
- PUR faucet filters piece of work for 100 gallons (380 L) of water, or most 3 months of use.
- Don't run h2o over 100 °F (38 °C) through the filter since you could damage it.
Warning: The water may sputter or look cloudy when y'all first use the new filter, only it will get meliorate as you lot run h2o through it.

Advertisement

Ask a Question

200 characters left

Include your email address to go a bulletin when this question is answered.

Submit

Many PUR filtration systems have electronic lights that detect when you need to change your filter. If y'all see a dark-green light flash, you lot don't demand to alter your filter. If it blinks yellow or red, then you need to supersede the filter soon.^[xi]

Thanks for submitting a tip for review!

Don't use water that'due south above 82 °F (28 °C) in a pitcher or over 100 °F (38 °C) through a faucet since it tin damage the filter.^[12]
Just utilise the filter with h2o that's already safety to potable since it will non remove leaner or infection.^[13]